FS: 2 CACTUS SOUNDS PF600.1

$575 SHIPPED FOR THE GRAY ONE (MISSING A SPEAKER SET SCREW)
$600 SHIPPED FOR THE BLACK ONE (COMES WITH BOX AND MANUAL) SOLD!!

Ahh poundstone's old amps!

First $1050 gets the pair shipped!!!

power output on 14 volts at .175 if they can take that low if not power output at .35?

Just gonna depend on impedance rise, at 1ohm 14.4 you should see around 4k

1 ohm each amp you should see 4k? so .35 they should make about 5k on a burp i guess?

heath these are my old amps we clamped 4k out of 1 with a starting imp of .25 rising just over 1.5 ohm with only 2 batts and stock alt. its got alot more in them just gotta get rise down. and ive burped them at .25 strapped but they dont like it anything below .25 per amp seems to just be a waste because by the time u roll into enuff you have lost the power u can get if u just wire to .25 per amp instead of .125 or whatever. lmk if u wanna know anything else about them and grab these beast so he can move them finally.lol

Are these still good for 0-600? How hard is it to get the missing set screw, what size is it?

thanks poundstone

Yeh i remember clamping poundstone's amps at the waukesha show.

Yeah good to go in 0-600. You can get the set srews at home depot, I may pick one for it in the next few days.

is that the only reason it is $25 less, or is there another difference besides the obvious heat sink color?

The Gray one is the older model and has more wear, the black one comes with the box and manual.

these are some bad ass amps i can personally vouch for them as strong as a d5 in my testing

here is one in my truck

https://www.youtube.com/watch?v=TKuNlFUO4sw

this was a legal record run this was actually the second run since darvile screwed up the first one of 156.3

https://www.youtube.com/watch?v=zcPFcxJhN3c&feature=grec_index

I see where these amps were posted before, and it was stated that the grey amp has a stripped set screw terminal, was this the actual setscrew or the block that it screws into?

sanman wrote:

this was a legal record run this was actually the second run since darvile screwed up the first one of 156.3

https://www.youtube.com/watch?v=zcPFcxJhN3c&feature=grec_index

Darville screw up?? Come on now...

I haven't messed with it since I got it, poundstone told me it was stripped, but not a big deal ill get it fixed today ,)

this amp is 600@4 ohms, and a monster

on the 157 run, what impedance were you at before rise? If you don't mind me asking?

If I were a gambling man i would probably bet from .23-.25

Yeah right around there, we ran em at .22 on 12v.

well that meter was a db off man and i wasnt in the truck thats 160 run for sure

.25

the only probly as you can see from the video was you have to get the roll down with the amount of voltage you run roll to quick and clip thats what took me so long in the video, and the reason that meter didnt read 159 draining batts

what is the dimensions of this amp? I didn't see any published on a site anywhere. - curious if it will fit under my seat.

same size as an m3 same case and all

ok, so 21.5" length, i have to make sure the amp does not protrude past the front seat bolts. So the M3 and PF600.1 are built by the same manufacturer?

Its a differant casing than the m3, has the american bass style casing.

Black one is sold, still have the gray one if anyones interested.

$550 SHIPPED FOR THE REMAINING GRAY ONE!!